Trailer Hitch Fit for 2019 Hyundai Ioniq Plug In Hybrid

Question

Question:

Wil this hitch fit my plug in Ioniq hybrid?

asked by: Eric A

0

Expert Reply:

Unfortunately, none of our hitch manufacturers offer a hitch that's compatible with the Hyundai Ioniq plug in hybrid.

If you were needing the hitch to carry bikes, a trunk mounted bike rack like the Yakima Fullback # Y02634 2-bike or # Y02633 for the 3-bike model.

expert reply by: Mike L

0

Answer 1

I can understand not wanting to remove or cut anything on your 2021 Toyota Highlander, but every single hitch for this vehicle requires some type of modification. There is one though, that requires the least amount, which is from Curt, and fits your…

view full answer...

Answer 2

We carry a very handy 2 inch ball mount for this exact application. The part is #D210. The ball mount slides and pins into your hitch and the top receiver will accept 2 inch bike racks and hold them above the ball. The Ball Mount has a 500 lb tongue…

view full answer...

Answer 3

It will not, unfortunately the trailer hitches we offer for the 2021 Kia Niro aren't compatible with plug in hybrid electric vehicles A/K/A PHEV's as the structure at the rear of the vehicle is different enough that the hitch won't fit.…

view full answer...

Answer 4

All of the trailer hitches for the 2012 Volkswagen New Beetle, turbo, are Class I trailer hitches with a 1-1/4 inch receiver. To use a 2 inch accessory like your bike rack, you would have to use a 1-1/4 to 2 inch adapter, #HTAD. The use of an adapter…

view full answer...

Answer 5

I checked with both Draw-Tite and Curt and unfortunately there is not a trailer hitch available for your 2019 Infiniti QX50. It looks like a trailer hitch has not been available for the Infiniti QX50 since 2017, so the likelihood that one will be…

view full answer...

Answer 6

At this current time we do not have a trailer hitch yet confirmed to fit your 2023 Mercedes-Benz E-Class. For the time being if you're trying to haul bikes I recommend The Yakima FullBack 2 Bike Rack #Y02634.This rack can hold up to two bikes…

view full answer...

Answer 7

If you have an a-frame type trailer frame a great option for transporting bikes is the Stromberg Carlson Bike Bunk #CC-275. This bolts on to a trailer's frame and fits frames from 14- to 55-inches wide. It provides a 2-inch receiver opening that…

view full answer...

Answer 8

In order to use a trunk mount bike rack like the Yakima FullBack 3 Bike Rack part #Y02633 on your 2013 Acura MDX while also towing a trailer you would indeed need to extend the connection point in order to prevent any turning clearance issues. For…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...