Compatibility of Solera Replacement Awning Fabric With a Dometic Awning With Metal Weather Guard

Question

Question:

Can this be installed with the metal cover I have on my Dometic AE Awning?

asked by: Susan

0

Expert Reply:

The Solera 17' Replacement Awning Fabric # LCV000334411 may work with the metal cover on your Dometic Awning. You will need to verify how the fabric attaches to your metal cover.

If the metal cover has a channel that the fabric slides into like the awning rail that is mounted on the side of your camper you will be able to use the fabric.

If the fabric is attached to the metal cover and then attaches to the awning rail on the side of the camper you will have to special order that from Dometic.

expert reply by: Bud M

0

Answer 1

The correct black Solera power awning upgrade kit you'd need is the part #LC434723 that you referenced. This would be exactly what you'd need and comes with everything needed to upgrade your Dometic 8500 manual awning to a powered setup! I…

view full answer...

Answer 2

Yes, a 20 foot wide Dometic A&E awning is compatible with the conversion kit with 69 inch arms; specifically, the Solera conversion kit is compatible with Dometic A&E awnings that have an 8 foot extension, and are models 8500, 9000, or 9100.…

view full answer...

Answer 3

For your Class A Motorhome you are probably going to want to use the Ultra-Fab Ultra Scissor Jacks part #UF48-979031 instead of the Ultra-Fab Ultra Scissor Jacks part #UF48-979002 as they offer more lift which will be needed. They are designed…

view full answer...

Answer 4

You can use this #LC329250 conversion kit if you have a pull style manual awning. These Solera Kits are compatible with your Dometic awnings and everything you need is included with the kit. I've provided a video for you to check out!

view full answer...

Answer 5

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 6

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 7

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 8

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 9

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 10

I spoke with Lippert in regards to your blinking touchpad on your Solera Smart Arm 12V Power RV Awning - 20' Wide #LC517517, and they explained to me that the reason that your touchpad is blinking is because a level 2 fault was detected. These…

view full answer...

Answer 11

There is a way for you to find out exactly where to place the center hanger of your 18 foot tandem axle trailer. If you take a look at the diagram I added, which is part of a help article I also linked on how to determine where to put your…

view full answer...