Differences Between Curt Trailer Hitches for 2022 Ford Escape

Question

Question:

I see that you show the # C23FR as a fit for the 2022 Ford Escape, but you used to sell a # CU56FR. What's the difference between the two?

asked by: Sal

0

Expert Reply:

Both the # C23FR (Curt 13454) and the CU56FR (Curt 13436) are fits for a 4th generation Ford Escape, however the CU56FR which isn't a fit for the popular Escape Hybrid has been phased out in favor of the redesigned # C23FR which DOES fit the hybrid.

If you'll be using the hitch for towing, you'll also need a trailer wiring harness like # TE54FR, a ball mount like # D-28 along with a # PC3 hitch pin and # 40038 for a 1-7/8 or # 63845 for a 2 inch trailer ball.

I've linked to install instructions and step by step videos for the # C23FR hitch and the # TE54FR trailer wiring harness.

expert reply by: Mike L

0

Answer 1

Yes, the Curt Trailer hitch Reciever #C23FR will fit your 2022 Ford Escape with the titanium package. This hitch will fit all models of the 2022 Ford Escape including the Titanium package.

view full answer...

Answer 2

The correct suspension enhancement air springs for your 2024 Ford Escape are the Air Lift 1000 Air Helper Springs for Coil Springs #AL32WQ.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 11

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 12

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...