Recommended Replacements For A MAXXAIR 0007000K Roof Vent

Question

Question:

I have two MAXXAIR 0007000K powered fans with lid opener problems. One will operate and raise/lower but the lowering and raising operation continues much longer than needed and you can hear gears skipping after full motion. The other unit the motor operates etc but the lid does nothing like it is no longer attached. Looking at your part #s MA10-20281K-1AF MA10-20222KS and trying to see if that makes sense. I appreciate any help you can provide.

asked by: Adam C

0

Expert Reply:

It definitely sounds like you need a replacement operator mechanism and lift arm for your MAXXAIR MaxxFan Deluxe # MA00-07000K. With that said, the # MA10-20281K-1AF and # MA10-20222KS will be the correct replacements for you. These will bolt right into your fans and get you working properly in no time.

expert reply by: Lazer S

0

Answer 1

I reached out to MaxxAir as I was stumped since you had replaced both the parts already. Their tech said you will want to first check the voltage going into and coming out of the Circuit Board #MA10A21275K with a Meter #PT29ZR where the lift motor…

view full answer...

Answer 2

My contact at MaxxAir advised that there are three potential causes for the beep and no fan motion you're experiencing with your MaxxFan Trailer Roof Vent #MA00-04000K. One potential cause is that the unit was wired with incorrect polarity. Make…

view full answer...

Answer 3

I sent all of your info and pictures to MaxxAir to find out what circuit board you'd need and they told me the board you need is the part #MA10A21275K.

view full answer...

Answer 4

As a first step, disconnect power to the fan for a few minutes, then reconnect power to reset the circuit board #MA10A21275K. If the fan fails again it could be the circuit board. Your rain sensor could incorrectly think rain is present on the rain…

view full answer...

Answer 5

The two most likely causes of a MaxxAir vent fan lid not opening or closing are either going to be a lift motor or operator failure. I recommend removing the motor and applying power directly to this to see if the shaft turns. If not, you know the…

view full answer...

Answer 6

I spoke with my contact at MaxxAir regarding your vent like the MaxxFan #MA00-04500K. He said what you are experiencing might be caused by a short in the rain sensor. Since that light is coming off and on, this is likely the issue and what is also…

view full answer...

Answer 7

You definitely have a circuit board issue with your MaxxFan 7000K and need to replace it with the part #MA10A21275K and you'd be set.

view full answer...

Answer 8

For your MaxxFan roof vent you most likely need the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF. This replaces the powered lift function. It is best to access this from the top like you see in…

view full answer...

Answer 9

We do have the exact parts you need and yes you can order it through us! I verified with the manufacturer for you that the correct parts for your MaxxAir 4801K are the following: - Replacement Operator Mechanism #MA10-20281K-1AF - Replacement Lift…

view full answer...

Answer 10

From the numbers you provided it sounds like you have a MaxxFan 4700K model fan. The Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF is the correct replacement for the MaxxFan 4700K's.

view full answer...

Answer 11

For your MaxxFan 4951, you can use the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF to fix your broken operator mechanism.

view full answer...

Answer 12

I've attached an exploded diagram photo of the vent assembly that uses the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF for you to check out. You'll need to use it as a guide for…

view full answer...