What Do I Need to Install a Brake Controller on My 2013 Ford E-350 Without Factory Connector

Question

Question:

My 2013 E350 passenger van did not come with factory 4eay. What do I need to install brake controller and 7 pin connector From scratch There is a female plug stowed behind my pin holder but no other as seen on videos

asked by: John R

0

Expert Reply:

To add a brake controller to your 2013 Ford E-350 I recommend installing the following:

Curt T-Connector 4-Way - # C56020
Universal Wiring Kit - # ETBC7
Extra Wire - # 10-2-1
Mounting Bracket - # 18136
Primus IQ Brake Controller - # TK90160

The Curt wiring gives you the 4-Way that you need and then the additional 2 wiring kits and mounting bracket provide you with all of the wiring for a 7-Way and adding a brake controller. I really like the Primus IQ because it's one of the more budget-friendly controllers but it's really effective and it's also backed by a limited lifetime warranty so you can be confident in the quality.

I've attached some installation videos that will help you out if you plan on doing the install yourself.

expert reply by: Jon G

0

Answer 1

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more…

view full answer...

Answer 2

The connectors you have found are not confirmed to be for the trailer wiring and we don't have any wiring harness that is a fit for what you described. Because you don't have the factory trailer wiring, I recommend starting with the…

view full answer...

Answer 3

I have a suspicion about what might be causing the problem you mention. Do your trucks have 6-way trailer connectors? Or, do the trucks have 7-way connectors, but you are using a 6-way to 7-way adapters because the trailers use 6-way connectors?…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...