What Size Are the Bolts Used to Mount the Curt 13018 Hitch

Question

Question:

I need the size of those bolts

asked by: Medi

0

Expert Reply:

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13018 uses M14 x 5.50 grade 8 bolts. There are replacement hardware kits available for the Curt # 13018 by putting that part number into the field marked "Hitch Item Number" on the page for the # RHK.

I've also linked the instructions for this hitch that list the specs of the bolts and the washers.

expert reply by: Erik B

0

Answer 1

We do offer the replacement mounting bolts for the 60,000 lb Curt Pintle Hook #C48231. I checked with Curt and they are 5/8" diameter Grade 8 bolts, and the complete kit is the following: - Curt Bolt Kit #C48332 This kit is the required bolt kit…

view full answer...

Answer 2

Fortunately there is an easy solution to this issue. You need only to order the etrailer #RHK Replacement Hardware Kit. I have included a link to that product page. Just enter your hitch brand name (Curt) and the model number and we will ship you the…

view full answer...

Answer 3

The Curt Pintle Hook #C48231 is indeed rated for 60K GTW and 12K vertical load. I confirmed these specs with Curt. Those are high weight ratings but keep in mind that the nature of a pintle hook, which has a large amount of flat steel surface area to…

view full answer...

Answer 4

I had the bolt holes on the Super Titan Forged Pintle Hook Plate for 3" Trailer Hitches #RP38186 measured, and they are actually 5/8". That being said, I suggest going with the Curt Pintle Hook #C48215 to attach to it. This does include 1/2…

view full answer...

Answer 5

For a 3 inch hitch pintle hook setup Bhmllc what you'll need is the Super Titan Forged Pintle Hook Plate part #RP38186 which fits the 3 inch hitch size and has plate that a bolt on hook setup can attach to like with the Curt #C48231. We don't…

view full answer...

Answer 6

Most pintle hooks use a standard bolt pattern which is 3-3/8" horizontally center to center and 1-3/4" vertically center to center (see photo). Therefore, the Pintle Hook part #C48231 would be a direct fit and work well for you. It also…

view full answer...

Answer 7

The Curt Trailer Hitch Receiver part #13091 comes with four M12x1.25 hex bolts and four 1/2" conical tooth washers.

view full answer...

Answer 8

When installing the Curt #13018 on your 1999 Mercedes ML430, you will need to remove the bumper fascia. However, this actually isn't as difficult as it sounds as it is just a few bolts and it's off. I included an install video from a…

view full answer...

Answer 9

The closest option we have to the 3-1/2" x 2" bolt pattern you mentioned that your 1989 Land Rover Defender bumper has is the Curt #13018 which has a mounting hole pattern that measures 2-1/4" x 3-1/4" as shown in the included…

view full answer...

Answer 10

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #CU94FR is a confirmed fit for a 2022 Hyundai Tucson per the manufacturer. These are tested on the vehicle for function prior to releasing fit. There would be no…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Size Are the Bolts Used to Mount the Curt 13018 Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching