What Size Bolts Come with the Curt Trailer Hitch Receiver 13091

Question

Question:

do mounting bolts come with the curt 13091 and if so what size are they

asked by: Ralph H

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13091 comes with four M12x1.25 hex bolts and four 1/2" conical tooth washers.

expert reply by: Conner L

0

Answer 1

The closest option we have to the 3-1/2" x 2" bolt pattern you mentioned that your 1989 Land Rover Defender bumper has is the Curt #13018 which has a mounting hole pattern that measures 2-1/4" x 3-1/4" as shown in the included…

view full answer...

Answer 2

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 3

I do have a trailer hitch for your 1990 Mitsubishi Montero, but I spoke with my contact at Curt and he confirmed that the Curt Class III Trailer Hitch, #13091, was designed to fit only the 1992 to 2000 Mitsubishi Montero except the sport model. The…

view full answer...

Answer 4

When installing the Curt #13018 on your 1999 Mercedes ML430, you will need to remove the bumper fascia. However, this actually isn't as difficult as it sounds as it is just a few bolts and it's off. I included an install video from a…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #13018 uses M14 x 5.50 grade 8 bolts. There are replacement hardware kits available for the Curt #13018 by putting that part number into the field marked "Hitch Item Number"…

view full answer...

Answer 6

Unless otherwise noted from the tire manufacturer, you should run your tires at the full psi they are rated to. As an example, the Taskmaster 5.30R12 Radial Trailer Tire - Load Range C #TT53012C is rated to 1,050 pounds at 80 psi and should therein…

view full answer...

Answer 7

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #CU94FR is a confirmed fit for a 2022 Hyundai Tucson per the manufacturer. These are tested on the vehicle for function prior to releasing fit. There would be no…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

What Size Bolts Come with the Curt Trailer Hitch Receiver 13091

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching