What Is The Width Of The Kodiak Disc Brake Kit # K2HR526D?

Question

Question:

We have a trailer frame width of 73.125, spring center 71.125, 6000 Lb 4inch axle w/ 87inch hub face, 15inch wheels. Will your K2HR526D brake kit fit w/ no interference?

asked by: Ivan R

0

Expert Reply:

The Kodiak Disc Brake Kit # K2HR526D has a hub face to caliper bolt guide(which is the part closest to the trailer) measurement of 6.01".

With your measurements your current hub face to trailer frame measurement is 6.9375 on each side. This means you will not have any interference.

expert reply by: Bud M

0

K2HR526D Measurements
(click to enlarge)

Answer 1

The correct bearing buddy for the Hub part #KHR12D that you referenced would be based on the 15123 outer bearing that the hub uses. Based on that you would want the Bearing Buddy part #BB2441. Installing the Bearing Buddy is pretty easy and would not…

view full answer...

Answer 2

To get the best braking power for your boat trailer you would want to have disc brakes on both axles. If you happen to be limited to one axle then you would want the rear outfitted. With a 5,000lb boat you likely have two 3,500lb torsion axles. The…

view full answer...

Answer 3

There are a few things we need to know before you can pick out a disc brake kit for your Karavan Trailer. We have to determine what spindles you have on your trailer so we can replace you hub drums with hub rotors. To do that you will need to remove…

view full answer...

Answer 4

Thanks for all of the info on your current hubs! That makes picking out new ones very easy. The etrailer hub part #AKIHUB-545-35-G-EZ-K that you referenced is a confirmed fit and would work great. It's also galvanized which helps prevent…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

What Is The Width Of The Kodiak Disc Brake Kit # K2HR526D?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching