Does Demco Hijacker Autoslide for Ford OEM Rail Kits Fit 2022 Ford F-350

Question

Question:

Does the Demco sliding hitch 8550038 which fits the Ford 2021 puck system also fit the Ford 2022 factory installed puck system?

asked by: Edwin S

0

Expert Reply:

Yes the Demco Hijacker Autoslide part # DM8550038 that you referenced does fit the OEM Ford rail kit of a 2022 Ford F-350. It's a really great option for short bed trucks as it doesn't require you to get out and activate a slider when sharp turns are needed.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 4

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 5

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 7

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 8

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 9

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 10

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 11

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 12

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...