What Size Bolts To Install Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0

Question

Question:

What size of the self tapping bolt to mount the bracket to the I beam

asked by: Tommy

1

Helpful Expert Reply:

I reached out to my contact at Lippert and he mentioned that the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 # LC349975 has holes that are 0.57" diameter and designed for use with 1/2" diameter bolts.

expert reply by: Erik B

1

Answer 1

The Replacement Short Left Rear Leg #LC342610 uses 1/2"-20 x 1-1/2" bolts to attach to the Jack Bracket for Lippert Ground Control 3.0 #LC349975. I'm not entirely certain what you are referencing in terms of "whole…

view full answer...

Answer 2

Yes it does, what you will need are 1/2"-20 self-tapping bolts in order to install the bracket you asked about: - Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975

view full answer...

Answer 3

With the leg of your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 being that bent the auto-level feature would either not function at all (if it's damaged enough to sense there's an issue) or…

view full answer...

Answer 4

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 5

I have attached for you the installation manual of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817. This is a generic install manual that can be used on any trailer but there is not a set of instructions specific…

view full answer...

Answer 6

When you install the rear jacks of the Lippert Ground Control 3.0 you will use a 5/16 inch drill bit for the pilot holes so that the included self-tapping screws will attach. I attached a picture I took from the install instructions that covers the…

view full answer...

Answer 7

I reached out to Lippert to confirm that you can change out your 24-1/2" rear jacks that come with the 4-Point Lippert Ground Control 3.0 #LC358590 with the Short Left Rear Leg #LC342610 and Short Right Rear Leg #LC428493. They confirmed that…

view full answer...

Answer 8

It sounds like you're looking for the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975. This replaces the bracket on your Lippert Ground Control 3.0 #LC358590 or #LC675817. It does not come with hardware so you will need…

view full answer...

Answer 9

The rear sensor for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 has very specific mounting instructions to properly operate. You'll need to locate a crossmember on your frame right at the rear jacks or just…

view full answer...

Answer 10

I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the #LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam. If clearance…

view full answer...

Answer 11

I have attached for you below the complete dimensions of the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 part #LC349975 to the degree that Lippert was willing to share. If you require further dimensions, I'd need to know…

view full answer...

Answer 12

For the rear jacks in Lippert Ground Control 3.0 #LC358590 the bracket the jacks attach to have multiple holes and you will need to mount them so that when fully retracted the jacks have 7 to 9 inches clearance from the bottom of the foot to the…

view full answer...