What Size Holes Get Drilled in Frame for Install of Rear Jacks of Lippert Ground Control 3.0

Question

Question:

What size hole do you drill in the frame for the rear jacks?

asked by: Rick M

1

Helpful Expert Reply:

When you install the rear jacks of the Lippert Ground Control 3.0 you will use a 5/16 inch drill bit for the pilot holes so that the included self-tapping screws will attach.

I attached a picture I took from the install instructions that covers the install of the rear jacks.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Actually, the LCI #LC358590 Leveling System you referenced is a bolt-on system that wouldn't require welding. I've linked you to a video describing how the system works.

view full answer...

Answer 2

Lippert Ground Control 3.0 #LC358590 weighs approximately 225 pounds total. The shipping weight is 229 pounds so a little has to be subtracted to account for the packaging. It was designed for 5th wheel trailers though so installing it may require…

view full answer...

Answer 3

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the instructions…

view full answer...

Answer 4

The Lippert Ground Control leveling system #LC358590 will work well for you. The 4-points of stability and leveling are going to provide a more stable feeling when you are in the trailer without the additional expense of a 6-point system. As long as…

view full answer...

Answer 5

I checked the install instructions for the Lippert Ground Control 4 Point part #LC358590 that you referenced and the rear jacks can bolt on. If you check out the picture I attached you'll see the install of the rear jacks portion of the…

view full answer...

Answer 6

We haven't heard back on the install of the Lippert Ground Control 3.0 part #LC358590 that you referenced from our customers, but the install is pretty straight forward. The 2 landing gear jacks mount to existing points on your RV and secure with…

view full answer...

Answer 7

The larger and smaller control pads of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 are designed to work with each other and would not cause any type of interference. Are you referring to the larger touchpad that…

view full answer...

Answer 8

The 676004 number you provided as a replacement fuse for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 returns to a 30A fuse instead of a 35A fuse. That being said, we do not carry that fuse. You can however take your…

view full answer...

Answer 9

I reached out to my contact at Lippert and he mentioned that the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975 has holes that are 0.57" diameter and designed for use with 1/2" diameter bolts.

view full answer...

Answer 10

I reached out to Lippert to confirm that you can change out your 24-1/2" rear jacks that come with the 4-Point Lippert Ground Control 3.0 #LC358590 with the Short Left Rear Leg #LC342610 and Short Right Rear Leg #LC428493. They confirmed that…

view full answer...

Answer 11

I have attached for you the installation manual of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817. This is a generic install manual that can be used on any trailer but there is not a set of instructions specific…

view full answer...

Answer 12

Yes it does, what you will need are 1/2"-20 self-tapping bolts in order to install the bracket you asked about: - Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975

view full answer...

What Size Holes Get Drilled in Frame for Install of Rear Jacks of Lippert Ground Control 3.0

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching