MORryde Standard Frame Hanger X-Factor Crossmember Review Video

Customers compare MR33WR to these similar products

Products Featured in this Video

Review of the MORryde Standard Frame Hanger X-Factor Crossmember

Hey guys, welcome to etrailer and today we're gonna be taking a look at the MORryde X-Factor cross member for standard hangers. Trailer frames definitely aren't as strong as we'd like them to be. There tends to be quite a bit of bend in them, especially when you make sharp turns. You'll kind of see you'll flex a little bit side-to-side. So what this is going to do is it's going to strengthen… see more >

Info for this part was:

Video Edited:

Dustin K

Video Edited:

John S

Test Fit:

Jacob H

Test Fit:

Kevin C

Installed by:

Andy C

Video by:

Thomas T

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Explore Expert Info

Most Popular Wheel Bearings

Big Truck Big RV

Performance Chips and Modules

7 Steps to Clean Your RV Awning, Prevent Mold, and Save Money

30-Amp and 50-Amp RV Service: What's the Difference?

How to Measure a Trailer Axle

How to Raise Your Travel Trailer Height

Where Do the MORryde X-Factor Crossmembers Install

The MORryde X-Factor Crossmember part #MR33WR attaches to the leaf spring hangers which are located in-between and in the front and rear of each axle. I have attached a photo below to clarify. Therefore, you'll need three for full support on…

view full answer...

Can MORryde X-Factor Crossmember Install in Unused Hole on Front Hanger

You can use that upper hole on your hanger to install the #MR33WR. Make sure you don't tighten it down too much or you will pinch the leaf spring and it won't function properly. You will also need to make sure you have enough room to…

view full answer...

How To Install MORryde X-Factor Crossmember With Leaf Spring Hangers Wider Than 3

The MORryde X-Factor Crossmember part #MR33WR is designed for standard suspension so that is the one you will need to use. If your leaf spring hanger brackets are wider than 3" then you will need to drill per the instructions which I have…

view full answer...

Will the MORryde X-Factor Work With Frame Hangers That Have Gussets?

I spoke with MORryde and they said that the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR will work just fine with your frame hangers with gussets. You'll just need to use the circled items attached in the image below and…

view full answer...

Which MORryde X Factor Braces Do I Need for a Tandem Axle Trailer w/ CRE3000 Equalizers?

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Will MORryde X-Factor Crossmember Adapter Kit for Drop Down Allow Avoiding Drain Line

It is likely you can avoid the drain line when installing the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR by using the MORryde X-Factor Crossmember Adapter Kit for Drop Down Applications #MR43WR. I don't know exactly the…

view full answer...

MORryde CRE3000 Equalizers, X-Factor Cross Members & SumoSprings For 2020 Keystone Outback 291UBH

Thank you for the images. The MORryde Rubber Equalizers #MR87ZR are the correct set for your 2020 Keystone Outback Ultra-Lite 291UBH. You will pair this with the MORryde Suspension Upgrade Kit #MR46ZR. Instead of using the wet bolts included with the…

view full answer...

Which Hangers Should MORryde X-Factor Crossmembers Install On

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

MORryde X-Factor Crossmember that Fits MORryde CRE3000 Trailer Suspension

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part #MR33WR.

view full answer...

How Many MORryde X-Factor Crossmember Supports Are Needed For A Tandem Axle Trailer?

The MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR includes one adjustable crossmember. Your existing hardware will be too short due to the extra thickness of the crossmember, so you will need to add #MR58ZR if…

view full answer...

Hey Bill, sorry to hear about all the trouble you're having but after looking at the pictures you sent in I'd have to agree with the tech. I think you're going to need to up your springs to a beefier set like the 7-Leaf Double-Eye Spring…

view full answer...

Can Just One MORryde X-Factor Crossmember Be Used On A 2021 Jayco Jay Feather 25RB?

Yes you can just use one MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR with your 2021 Jayco Jay Feather 25RB, however for full support a tandem axle trailer will need to utilize 3. Attached is a product overview…

view full answer...