Could Valterra Waste Valve T58 Stop Leak Up Stream from It

Question

Question:

T=58 waste value will this work to stop a leaking black tank valve leak, my hubby started working trying to get black tank valve off, its so buried its almost impossible, we have a 1999 Fleetwood prowler will this work

asked by: Sherri W

0

Expert Reply:

Sounds like you are asking if you were to install the Valterra Waste Valve part # T58 on the bayonet fittings of your black water valve if it would prevent a leak further upstream from passing through it? If so, yes that would technically work.

expert reply by: Jameson C

0

Answer 1

As a clarification, all valves, including the #T1003VPM, include seals, as pictured in picture 10 on the product page. However, I can see that your 3" waste valve is missing it's seals. I would not buy a new complete valve when all…

view full answer...

Answer 2

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 3

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 9

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 12

To wire two 6-volt batteries in series to produce 12-volts, you would connect the load to the positive terminal of battery #1. Connect the negative terminal of battery #1 to the positive terminal of battery #2. Ground the negative terminal of battery…

view full answer...

Could Valterra Waste Valve T58 Stop Leak Up Stream from It

Product Page this Question was Asked From

Continue Researching