How Wide is the Center Flat Cap on the Phoenix USA Quick Trim Hub Cover for 8 on 6-1/2 Bolt Pattern

Question

Question:

Can you please tell me what the diameter measurement is of the center flat area of the cap item #PXQT765CHN ? The area that I’m referencing says etrailer on it. Thanks for your help!

asked by: Becki Z

0

Expert Reply:

The Phoenix USA QuickTrim Hub Cover - 8 on 6-1/2" Bolt Circle - ABS Plastic - Chrome - Qty 1 # PXQT765CHN is 4-7/8" on the inside and 4-1/8" on the top/outside when measured.

expert reply by: Erik B

0

dimensions of flat top of cap
(click to enlarge)

Answer 1

Both QuickTrim Trailer hub covers are for wheels with 8 on 6-1/2 bolt patterns, but the #PXQT765CHN is for 13/16 inch lug nuts and the #PXQT865CHN is for 7/8 inch lug nuts.

view full answer...

Answer 2

From previous questions I'm fairly certain your seal 212337313TB is the same as the #GS-2250DL which has an inner diameter of 2.250 inch and outer diameter of 3.376 inch.

view full answer...

Answer 3

Yes. The Phoenix USA QuickTrim Hub Cover - 8 on 6-1/2" Bolt Circle - ABS Plastic - Chrome - Qty 1 #PXQT765CHN typically will fit on 13/16" lug nuts; when you convert to metric that's about 20.5mm, so the .5mm would be within the margin…

view full answer...

Answer 4

If you wanted the ability to cut all power to your Prodigy P3 Brake Controller part #90195 you easily could do this by running a switch on either the power (black), or ground (white), wire although it is not recommended. For a switch you could use…

view full answer...

Answer 5

The 10 inch Electric Brake Assembly, #23-26, requires a 7/16 inch, fine thread bolt for installation. Use part #6-17 for installation. The lock washer is also 7/16 inch. Part #5-8 is the correct washer for this application.

view full answer...

Answer 6

The kit you are looking for is the part #BRKH10B which is nuts and lock washers needed to install the brake assemblies part #AKEBRK-35-SA that you referenced. The nut size is 7/16-20.

view full answer...

Answer 7

I went out the warehouse to measure the Phoenix USA QuickTrim Hub Cover for Trailer Wheels - 8 on 6-1/2 - ABS Plastic - Chrome - Qty 1 #PXQT865CHN. The depth at the center of the hub is 4-1/8 inches and the depth at your 7/8 inch lugs is 2-3/8…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...