Can the Tekonsha P3 Brake Controller Be Wired to an On/Off Switch
Question:
I purchased a Tekonsha P3 from etrailer.com for a previous vehicle and used the quick release bracket to remove it when I wasnt towing. I now plan to install it permanently in my new to me vehicle 2011 Nissan Frontier. I have purchased the connector to run from the Nissan factory tow harness to the brake controller. I do not want the brake controller powered up when I am not towing. Is there any reason I cannot wire an on/off toggle switch to interrupt the black wire on the connector for this purpose? If I can install such a switch, will a 20 amp switch and 12 gauge wire suffice? Thanks.
asked by: Matt
Expert Reply:
If you wanted the ability to cut all power to your Prodigy P3 Brake Controller part # 90195 you easily could do this by running a switch on either the power (black), or ground (white), wire although it is not recommended. For a switch you could use the # D16740 and then for 12 gauge wire you could use the # 12-1-1 sold by the foot. This isn't recommended as you'd lose all presets when you cut power to the controller and have to start over every time.
For the permanent mount bracket for the P3 you would want the part # TK5904.
Products Referenced in This Question
Derale Lighted On/Off Switch for Electric Fans
- Accessories and Parts
- Radiator Fans
- Switches
- Derale
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Phoenix USA QuickTrim Hub Cover for Trailer Wheels - 6 on 5-1/2 - ABS Plastic - Chrome - Qty 1
- Shop: Phoenix USA QuickTrim Hub Cover - 8 on 6-1/2" Bolt Circle - ABS Plastic - Chrome - Qty 1
- Q&A: How Wide is the Center Flat Cap on the Phoenix USA Quick Trim Hub Cover for 8 on 6-1/2 Bolt Pattern
- Q&A: Will the Phoenix USA Quick Trim Hub Cover for 8 on 6-1/2 Bolt Pattern Wheels Fit 21mm Lug Nuts
- Video: Phoenix USA Tires and Wheels PXQT765CHN Review
- Shop: Mounting Bolts and Hardware for 12" Brake Assemblies
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 1/2" Studs
- Q&A: Correct Size Nuts and Washers for Electric Brake 23-26 Assembly
- Q&A: Nut and Washer Size For Installing Trailer Brake Assemblies # AKEBRK-35-SA
- Shop: Brake Controller
- Shop: Mounting Pocket for Tekonsha Prodigy Proportional Brake Controller
- Article: Brake Controller Installation: Starting from Scratch
- Video: HydraStar Electric Over Hydraulic Disc Brake Actuator Installation
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer brake controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Search Results: brake controller
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Trailer Wiring
- Search Results: hitch
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Review
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
on Trailer Brake Controller
