How Difficult IS The Curt Trailer Hitch Receiver # C12114 To Install On My 2012 Lexus LS 460?

Question

Question:

hi do you have a video for installing a trailer hitch for 2012 lexus ls 460

asked by: Jason

0

Expert Reply:

The manufacturers instructions includes several color pictures that were taken through the installation process. I have linked them below for you to reference.

Currently we do not have a video available for the installation of the Curt Trailer Hitch Receiver # C12114 for your 2012 Lexus LS460.

Curt rates the installation as a challenging installation as removal of the rear bumper is required and trimming of the underbody panel. They estimate that it will take a novice installer 3 hours to complete the installation.

expert reply by: Bud M

0

Answer 1

We do offer aftermarket trailer hitches that are designed to fit your 2014 GX 460. The trailer hitch I recommend is the Draw-Tite Max-Frame Trailer Hitch, part #75685. This is a Class lll hitch and it has a 2-inch receiver opening. We do not have any…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...