Bracket and Mounting Hole Measurements for a Curt C13149

Question

Question:

What are the lengths of the arms and the distance to where the bolts are.

asked by: Sean S

0

Expert Reply:

I spoke to a tech over at Curt and the arm brackets on the # C13149 have an overall length of 10 1/2 inches. The mounting holes are 7 inches apart from center to center. Please keep in mind this is custom fit for a 2006 to 2018 Honda RAV4.

expert reply by: Lazer S

0

Answer 1

When we installed the Draw Tite hitch part #e98864 you referenced on a similar 2007 Toyota RAV4 we found that from the center of the hitch pin out to the furthest point out on the rear spare measured 7 inches. So basically, as long as your bike rack…

view full answer...

Answer 2

Thank you for your purchase from etrailer of the Curt Trailer Hitch Receiver #C13149 for your 2014 Toyota RAV4. The bolts aren't too big, you just need to clean the weld nuts. What you'll need to do is use a spray lubricant such as WD-40, and…

view full answer...

Answer 3

When we installed Curt Class III hitch #C13149 on the 2012 Toyota RAV4 the hitch pin hole on the receiver tube was positioned about 5-1/2-inches forward of the rear-mounted spare tire cover. I suspect this is why you're looking at a hitch…

view full answer...

Answer 4

You will not have any fitment issues with the etrailer Trailer Hitch Receiver #e98864 on your 2010 Toyota RAV4 sport. You might also add the Bracket #18144 which will hold your 4-way flat connector in place. I recommend the T-One Vehicle Wiring…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 8

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Bracket and Mounting Hole Measurements for a Curt C13149

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching