2001 Haulmark Replacement Hasp

Question

Question:

Hello, i need help finding replacement hasps for our 2001 Haulmark trailer. The measurement from hole to hole is 5. Is there such a part available?

asked by: Wolff B

0

Expert Reply:

The biggest Hasp we carry is the Replacement Hasp for Polar Cam-Action Latch Kits - 1" Wide - Zinc-Plated Steel # 158-101 which has a 4-1/4" measurement from center to center of the bolt holes. Since the length of the hasp is 5-1/8" the body of it should cover the holes so no one can see them. I recommend filling the old holes with some silicone caulk # LT37467 and also putting some in the new holes to prevent water damage.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 10

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...