What is the Retracted Length of the Tubes on the Landing Gear Set RVLG-8000

Question

Question:

What is the height of the black outer tubes on part rvlg-8000 landing gear?

asked by: Tracy M

0

Expert Reply:

The height of the outer tubes on the Landing Gear Set - 36-1/2" Lift - 8,000 lbs # RVLG-8000 is roughly 29" without the legs and 32-3/4" with the drop legs included. The distance between the outer edges of the top and bottom weld stops is 17-1/2" and the distance between the inner edges is 15-1/2". This will be important to know since it's where the landing gear will mount to your coach, so you'll want to know the distance between the weld stops where your current landing gear are mounted.

expert reply by: Erik B

0

Dimensions
(click to enlarge)

Answer 1

The Landing Gear Set w/ Handle part #RVLG-8HDL have a one year warranty and they are designed to replace existing landing gear legs with 15-1/2" between the weld stops (inside to inside). I suspect this is what you have as it's an industry…

view full answer...

Answer 2

The foam ring on the Ventline Vanair Trailer Roof Vent part #VP-543SP is a weather seal that is used to help seal the dome on the fan assembly. If you continue to use the fan without the foam ring you would be subjected to leaks which could then…

view full answer...

Answer 3

According to my contact at Ultra-Fab, their Deluxe Electric Landing Gear Set #UF17-943010 has an overall height, including the motor assembly, of 36.55-inches with the leg fully retracted. Please refer to the linked diagram for the rest of the…

view full answer...

Answer 4

Thank you for providing that picture. In order to install the #SSR54FR on your Dometic AC you will start by removing the white wire coming from the compressor to the run capacitor and connect it to the blue wire on the SoftStartRV. Next, take the…

view full answer...

Answer 5

It is possible to replace just one leg of your 5th wheel landing gear. You will just need to confirm if it is the lead/driver leg or the follow leg. Usually the lead leg is on the driver side and the follow leg is on the passenger side. You'll…

view full answer...

Answer 6

The Landing Gear Set w/ Handle #RVLG-8HDL that you're interested in sounds like to be a perfect match for you! This landing gear set has an overall width of 6-1/8" including the foot pad, and the legs itself measure 2-1/2" wide like…

view full answer...

Answer 7

It sounds like you might have an Ultra-Fab landing gear set. I have included a diagram showing how the system gets wired. On it the white wire is the power wire and the green wire is the ground.

view full answer...

Answer 8

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 9

Normally when people say they have a 11-1/2 inches they are measuring between the brackets like you mentioned but the measurement to look for is on the outsides which for you would be 15-1/2 inches and the etrailer Landing Gear Set, part #RVLG-8000…

view full answer...

Answer 10

Atwood was sold to Dometic a few years back and replacement parts for the older landing gear have not been produced in awhile. Instead of trying to source a replacement leg and worrying about the next part failing I recommend replacing the older…

view full answer...

Answer 11

When it comes to landing gear like the Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs #LC333964, weld-on refers to the installation process. In order to install this landing gear set you will need to have a certified welder…

view full answer...

Answer 12

Your Atwood landing gear set is made to the very common dimensions for landing gear so we have plenty of options that will bolt right up. I really like the Bulldog landing gear part #BD500162 which is a manual crank or the Reese #RP500708 which has…

view full answer...