Overall Height Including Motor of Ultra Fab Landing Gear UF17-943010

Question

Question:

I want to adapt the UF17-943010 Ultra Fab landing gear set to my 2008 3305 Weekend Warrior Fifth Wheel. Request some specs. 1. What is the overall length of the unit? 2. What is the width of the unit between the clamps? 3. What is the motor height? 4. What is the distance from the bottom of the unit, not including the legs, to the top of the bottom weld stop? 5. One picture shows the distance between weld stops at 14 1/2 inches and the other at 19 inches, which is correct? Thanks for your time......

asked by: Ray H

0

Expert Reply:

According to my contact at Ultra-Fab, their Deluxe Electric Landing Gear Set # UF17-943010 has an overall height, including the motor assembly, of 36.55-inches with the leg fully retracted.

Please refer to the linked diagram for the rest of the dimensions you requested. What you see are the dimensions we got from Ultra Fab.

The width between the clamps will be the same as the distance from outside to outside on the mounting tabs, 14-1/2 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The foam ring on the Ventline Vanair Trailer Roof Vent part #VP-543SP is a weather seal that is used to help seal the dome on the fan assembly. If you continue to use the fan without the foam ring you would be subjected to leaks which could then…

view full answer...

Answer 2

The height of the outer tubes on the Landing Gear Set - 36-1/2" Lift - 8,000 lbs #RVLG-8000 is roughly 29" without the legs and 32-3/4" with the drop legs included. The distance between the outer edges of the top and bottom weld stops…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 7

As you have a Coleman Mach system currently you can use the Furrion Chill AC units from the list below. These will simply replace only the rooftop units and the controls and thermostats you currently have in place with control the new AC's. 13.5K…

view full answer...

Answer 8

Yes, you will be able to use the Furrion Chill HE RV Air Conditioner System #FR87FJ to replace all your Coleman MACH components. The thermostat will be able to control your furnace and run off the thermostat wiring your Coleman AC uses.

view full answer...

Answer 9

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 10

For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates I'd recommend going with the Roadmaster Direct-Connect Base Plate Kit #RM-523204-5. These are just as good as…

view full answer...

Overall Height Including Motor of Ultra Fab Landing Gear UF17-943010

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching