Tail Light replacement for Kaper L16-0053

Question

Question:

Looking for replacement lenses for this type of light Kaper L16-0053 which is a tail light/reverse combo. Measures around 4x6. Notice how the clear for the backup lamp is offset. Do you have anything that might work?

asked by: Jeff

0

Expert Reply:

The closest replacement taillight that we have to the light that you have is the Fusion LED Trailer Tail Light # STL211XRFHB. This tail light has the back-up light feature that yours also has. The difference is in the dimensions. The size of this light is 7-1/2" wide x 3-1/4" tall x 3/4" deep.

expert reply by: Jacob H

0

Answer 1

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 2

It sounds like your trailer has the 6-1/2 inch Oval stop turn and tail lamps and some side marker lamps that use a rubber grommet like the 6-1/2 inch oval tail lights grommet, #A70GB. Since the area where your lights are mounted is not accessible…

view full answer...

Answer 3

The marker and clearance lights you have now ground with a single wire hence why you have two wires total, one for power and one for ground. If the marker or clearance light only has one wire then this wire is for power and the light grounds though…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 8

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Tail Light replacement for Kaper L16-0053

Product Page this Question was Asked From

Continue Researching