Availability of 7-Way Trailer Wiring Harness with Mounting Bracket for 2011 Honda Pilot

Question

Question:

I have a 2011 honda pilot ex_l and want to purchase the curt 7 pole wiring harness kit but when I put in the part number it doesnt come up I want that kit since it comes with everything including mounting bracket

asked by: Thomas V

0

Expert Reply:

Curt still does offer a wiring harness for your 2011 Honda Pilot but it's a 4-pole connector, part # C56365.

We do have a solution for you with the 7-Way Tekonsha kit part # 118253 and the 7-Way bracket # PK12711U (sold separately).

expert reply by: Jameson C

0

Answer 1

The final authority on whether or not a vehicle has the tow package would be a Honda dealer. If you give them your VIN they will be able to tell you for sure. That being said, we have found that either kit will fit your 2011 Honda Pilot.

view full answer...

Answer 2

You did quite a bit of troubleshooting and homework on this so I commend you for that! Since it's not the relays, the fuses, or the trailer wiring that basically leaves the converter box of the wiring kit. Which you can test that with a circuit…

view full answer...

Answer 3

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56365 will not require any further fuses for your 2011 Honda Pilot. If you followed the instructions as outlined in the attached installation instructions, you will be…

view full answer...

Answer 4

Which wiring harness you need for your 2011 Honda Pilot 4WD is dependent on what you plan on plugging the harness into. The Tow Ready #118491 and the Curt #C56365 are the custom fit harnesses that will give you a 4-way end to plug into typically a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...