Correct Trailer Hitch Fit for a 2016 Mini Countryman S ALL4

Question

Question:

I just purchased a 2016 Countryman S ALL4 and need a towing solution for up to 1500 lbs. Will the c11333 work?

asked by: Bob

0

Expert Reply:

The Curt Trailer Hitch Receiver part # C11333 is indeed a fit for a 2016 Mini Countryman S ALL4 and has a 2,000 lb weight capacity.

expert reply by: Conner L

0

Answer 1

The Curt Trailer Hitch Receiver part #C11333 is a fit for all models of a 2016 Mini Countryman excluding John Cooper Works Editions. It does require trimming of the underside of the rear bumper fascia, but this is plastic. This hitch is rated as…

view full answer...

Answer 2

When we installed the Curt hitch part #C11333 on a 2013 Mini Countryman similar to your 2015 model we found that from the top of the hitch opening to the ground measured 10 inches. That would mean from the bottom of the hitch to the ground would…

view full answer...

Answer 3

For your 2012 Mini Countryman S, I recommend the Curt Class I Hitch #C11333. This Class I hitch is confirmed to fit your vehicle and will use existing holes in its frame for a no-drill installation. It will provide you with a 1-1/4 inch receiver…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 12

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Correct Trailer Hitch Fit for a 2016 Mini Countryman S ALL4

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching