Does Hopkins 7-Way/4-Way HM54FR Fit 2020 Chevy Silverado 2500

Question

Question:

2020 silverado 2500hd my truck already has a trailer hitch with plug mounted in the bumper. Will this harness plug into a separate box? So I can use both because I pull two different trailers in one day.

asked by: Gary H

0

Expert Reply:

The Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole and 4-Pole Connector # HM54FR that you referenced does fit your 2020 Chevy Silverado 2500 and gives you the ability to install a 7-way/4-way in the bed of your truck.

This plugs into the back of an active 7-way and allows you to put an additional 7-way in the bed of the truck via the longer harness that comes with it.

expert reply by: Jameson C

0

Answer 1

There is a 5th wheel wiring harness for your 2020 Chevy Silverado that was designed to fit perfectly in the factory cut out in your truck bed. The harness you need is the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness #HM54FR. I…

view full answer...

Answer 2

The Hopkins Endurance 5th Wheel/Gooseneck Wiring Harness #HM54FR that you referenced is designed for exactly what you described. This is going to plug in-line with the factory 7-Way at the bumper of your Sierra 2500 to provide you with a separate…

view full answer...

Answer 3

The problem that you would run into with a folding cover such as #BAK72331 is if you leave it on but folded up flat it will be several inches above the truck bed sides. This means that when making tight turns the trailer's pin box could…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...