Hitch Extender Needed for Reese # 38023 Super Titan Weld On 3 Inch Hitch

Question

Question:

I HAVE A CUSTOMER THAT WOULD LIKE TO HAVE THIS INSTALLED. HELL BE PULLING A BOAT ND WILL NEED A 48inch EXTENSION. LIKE THE OTHER BRAND SALES IS THERE ON AVAILABLE FOR THE HITCH?

asked by: STEVE

0

Expert Reply:

There is indeed an extender available, part # RP45292. However, in order to make it work, you'd need to use a reducer like the Draw-Tite # 58550. At the full 34 inch length, the extender will have a 4,500 lb towing/450 lb tongue weight capacity.

expert reply by: Mike L

0

Answer 1

I have a solution for you, however, the TorkLift Cannon Hitch Extension #TLE1636 that you were looking at is only for the Ford OEM 3" trailer hitch receiver and it will not fit your 2021 Ram 3500. It looks like the available receivers for your…

view full answer...

Answer 2

While the Draw Tite hitch reducer part #58550 doesn't have a specified weight rating it would easily handle towing a 30 foot trailer without any issues.

view full answer...

Answer 3

The only solution we have for a hitch extension as long as you are wanting for your 2011 Ram 3500 would be to first install a Torklift SuperHitch part #TLD1102 so that you could use a TorkLift SuperTruss Hitch Extension #TLE1536 which requires the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The 07100 bearing number you referenced is an older bearing that has the same dimensions as #L44643. If both the inner and outer bearings on your existing trailer are the 07100/ #L44643, and the hub has a 4 on 4 inch bolt pattern, the correct…

view full answer...