Correct TorkLift Frame-Mounted Camper Tie-Downs for a 2008 Ford F-350 Short Bed Factory Hitch

Question

Question:

Hi, i have a 2008 F350 crew cab short bed and i want to purchase frame overhead camper tie downs. I found this part, is this correct fit for my vehicle? It has a factory hitch and no steps. thanks

asked by: Alfredo G

0

Expert Reply:

The correct TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2008 Ford F-350 Short Bed No Step Factory Hitch is part # TLF2012 for the front and part # TLF3004 for the rear. These can then be paired with the TorkLift Locking FastGun Turnbuckles part # TLS9522-2-LK to complete your setup.

expert reply by: Conner L

0

Answer 1

I attached a couple pictures that I took from the install instructions for the Torklift Tie Down part #TLF2012 that you have that shows how all of the brackets bolt together. Hopefully that answers your question about how the plates all bolt…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 3

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory…

view full answer...

Answer 6

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover,…

view full answer...

Answer 7

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift…

view full answer...

Answer 8

Hey Bob, the Torklift Talon tie downs part #TL73QR weighs 35 lb. The TorkLift Talon Camper Tie-Downs #TL44XR weigh 26 lb. TorkLift Locking FastGun Turnbuckles #TLS9529-2-LK weighs 20 lb.

view full answer...

Answer 9

The F2032 you're looking for is under part #TL87CR on our website and would be the correct fit for your 2024 Ford F-350. For the rear tie-downs you'll need part #TLF3008. To complete the setup you can use the TorkLift AnchorGuard…

view full answer...

Answer 10

Of the two part numbers you mentioned only the #TLF2022A is a fit for your 2022 Ford F-350 short bed without factory board and with the factory installed hitch. You might have meant to type #TLF2022 which is the non-aluminum/stainless steel option…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Correct TorkLift Frame-Mounted Camper Tie-Downs for a 2008 Ford F-350 Short Bed Factory Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching