Does Curt Hitch 13358 Fit 2014 Mercedes Benz Sprinter with 144 inch Wheelbase and Rear Step

Question

Question:

The information on you page states that this is not for the 144 sprinter passenger with rear step. Can you confirm? I emailed earlier and have not heard back yet.

asked by: Jeff J

0

Expert Reply:

We have confirmed with Curt that the hitch part # 13358 does fit the 144 inch wheelbase models of the Sprinter vans that have the rear steps so it would work great for you.

expert reply by: Jameson C

0

Answer 1

It's an exhaust placement issue that prevents the Curt hitch part #13358 from fitting the passenger van versions of the 2011 Mercedes Benz Sprinter 2500. That's why you'd need the Draw Tite #75549.

view full answer...

Answer 2

For your Sprinter 2500, I recommend the Curt Trailer Hitch Receiver #13358 that will do a great job for your bike carrier and more should you decide to tow later. This hitch model is designed for either the 144" or 170" wheelbase Sprinter…

view full answer...

Answer 3

If the bolts on your Curt Trailer Hitch Receiver - Custom Fit - Class III #13358 are a little over torque that is not a big deal and should not pose an issue. If you don't feel good about it and would rather just replace the hardware, you are…

view full answer...

Answer 4

For the 2017 Coachmen Prism 2200LE built on a Mercedes Benz 3500 chassis we do have the Curt hitch part #13358 which has a 5,000 lb trailer towing capacity. Only thing you'll want to check is that your frame does not measure 30-3/8 inches wide…

view full answer...

Answer 5

A trailer weighing 8000 lb would be about twice the 4100 lb towing capacity of your 2001 Dodge Durango, according to what I found online. I wasn't able to find a pdf copy of the owner's manual online, so I'd recommend checking your…

view full answer...

Answer 6

We do have a trailer hitch fit for your 2016 Mercedes Benz Sprinter 2500 that has the factory step bumper. The Curt hitch part #13358 would be what you need. This fits either length wheelbase as well. In the picture I attached you can see the hitch…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...