Replacement Hardware Kit For A Curt Hitch On A 2021 Mercedes-Benz Sprinter 2500
Question:
Hello, I recently installed the 13358 Class III hitch. Due to rust on the existing bolts, I opted to use anti-seize on the threads. I forgot to lower the torque on the bolts due to the addition of the anti-seize lubricant and think that I may have overtorqued the bolts as I used the 79 ft-lb. I was wondering if I should replace the bolts on the hitch and re-install them without lubricant, torqued to the specified 79 ft-lb. If so, do you know where I can get replacement hardware? Thank you!
asked by: Warrick
Expert Reply:
If the bolts on your Curt Trailer Hitch Receiver - Custom Fit - Class III # 13358 are a little over torque that is not a big deal and should not pose an issue.
If you don't feel good about it and would rather just replace the hardware, you are going to need M12 x 1.75 Hex bolts, with a .375 x 1.25 x 2.00" round hole spacer, with a M12 x 1.75 flange nut.
Or
You can use our replacement hardware kit # RHK which will contain all the needed hardware for installation. For the "hitch item number" you will just need to type 13358 for your hitch and you'll be good to go.
If you have any other questions feel free to reach out.
Products Referenced in This Question
Replacement Hardware Kit for Trailer Hitches
- Accessories and Parts
- Trailer Hitch
- Hardware
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Replacement Hardware Kit for Trailer Hitches
- Search Results: 13358
- Video: Trailer Hitch Installation - 2013 Mercedes-Benz Sprinter
- Q&A: Trailer Hitch that Fits 2017 Mercedes Benz Sprinter 2500 with Factory Step Exhaust
- Shop: Replacement Hardware Kit for EcoHitch Trailer Hitch
- Video: Trailer Hitch Installation - 2008 Dodge Sprinter Van
- Search Results: c13388
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Higher Capacity Trailer Hitch that Fits 2017 Coachmen Prism 2200LE
- Q&A: Highest Capacity Hitch Available for 2001 Dodge Durango
- Q&A: Does Curt Hitch 13358 Fit 2014 Mercedes Benz Sprinter with 144 inch Wheelbase and Rear Step
- Shop: Replacement Hardware Kit for Curt SecureLatch Pintle Mount
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: What is the Best Hitch for a 2023 Mercedes-Benz Sprinter 2500 w/ Factory Step Bumper?
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Video: Choosing the Right Brake Controller
- Search Results: hitch
- Q&A: What Are The Torque Specs for 5/8" Lug Studs and Flange Nuts
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Roof Rack
- Video: etrailer Hitch Pin Alignment Collar Review
- Search Results: trailer hitch wiring
- Article: My Trailer Hitch Doesn't Fit
on Trailer Hitch
