Does Demco Fifth Wheel Rail Kit Adapter for 2020 GMC Sierra Fit with Bed Mat

Question

Question:

I have a factory rubber bed mat. Can this be mounted by placing holes in the mat or does it have to be mounted directly to the bed? I plan on using the andersen 3200 hitch. 2020 gmc sierra 2500 HD diesel

asked by: Patrick D

0

Expert Reply:

The Demco 5th Wheel Rail Adapter # DM6333 would need to attach directly to the metal floor of your 2020 GMC Sierra 2500. If you have a thick rubber mat you'd need to trim out a square or remove it altogether.

expert reply by: Jameson C

0

Answer 1

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 2

Depending on the total loaded weight of the fifth wheel you get, your 2009 Chevrolet Silverado 2500 HD should work for you. I did some research and found that GM has given the 2500 HD a maximum fifth wheel towing capacity of 16,700-lbs. What exactly…

view full answer...

Answer 3

I do have an option for you but you cannot mix and match base rails and frame brackets. Therefore, you'll have to purchase an entire new mounting kit, complete with frame brackets and base rails. I recommend the Demco Hijacker Premier Series…

view full answer...

Answer 4

We do have an adapter that will allow you to mount your PullRite SuperGlide 5th wheel hitch to your 2021 Ram 2500 with the factory puck system, so long as the SuperGlide is the ISR series (ISR stands for Industry Standard Rails). If you do have the…

view full answer...

Answer 5

The pucks on the Demco 5th Wheel Rail Adapter for Chevy/GMC OEM 5th Wheel Towing Prep Package #DM6194 just drop into the openings in your 2019 Chevrolet Silverado's OEM prep package, they are not actually locking in at that point. The Hex key…

view full answer...

Answer 6

The Demco 5th Wheel Rail Adapter #DM6099 that you referenced will work for you as it will give you a set of industry standard fifth wheel rails that your Husky hitch will fit in to. The center install slots of this rail kit are right at 20-1/2…

view full answer...

Answer 7

If the PullRite Superglide hitch is one that was intended to fit the industry standard style of rails then yes the Demco Rail Kit adapter part #DM6099 will work with it. I attached a picture that shows a Superglide hitch installed in the rail kit for…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...