What Are the Torque Specs for the Curt 2" Hitch Ball

Question

Question:

What is the recommended torque specification for attaching the ball to the receiver?

asked by: Victor K

1

Helpful Expert Reply:

The 2" Hitch Ball part # 40038 has a 1" shank so the torque spec will be 250 ft. lbs.

expert reply by: Conner L

1

Answer 1

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 2

The Replacement 42" Cable for Breakaway Switch from Bright Way Group, #3802350, will fit most models of ESCO break away switches. If you don't want to take a chance on it not fitting, I would instead recommend replacing the switch with part…

view full answer...

Answer 3

A weight distribution system is not required to tow with your 2017 Dodge Grand Caravan, though a system is recommended if your trailer weight is more than 50 percent of your vehicle's GVWR. Even a small pop-up is going to surpass the 50 percent…

view full answer...

Answer 4

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 5

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 6

Yes, we sure do! For your Ignik FireCan Fire Pit Rocks #GN47FR, you can use the Ignik FireCan Portable Fire Pit with 5' Hose - Propane #GN24FR. This is a portable fire pit that works great with the Ignik FireCan Fire Pit Rocks #GN47FR, measures…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The only differences between the Demco Trailer Coupler #DM14976-52 and #DM88XR are the colors and the mounting bracket design. The part DM14976-52 is silver and has a straight, or no-drop, design with the bottom of the coupler being towards the top…

view full answer...

What Are the Torque Specs for the Curt 2" Hitch Ball

Product Page this Question was Asked From

Continue Researching