Recommended Portable Fire Pit That Works With The Ignik FireCan Fire Pit Rocks

Question

Question:

Hi, I am looking for a portable fire pit for the fire pit rocks? Do you have that

asked by: Alex W

0

Expert Reply:

Yes, we sure do!

For your Ignik FireCan Fire Pit Rocks # GN47FR, you can use the Ignik FireCan Portable Fire Pit with 5' Hose - Propane # GN24FR.

This is a portable fire pit that works great with the Ignik FireCan Fire Pit Rocks # GN47FR, measures 7-1/8" long, 15-1/4" wide, 11-3/8" tall and includes a quick-connect hose with Type 1 fitting and adjustable regulator.

expert reply by: Bryce D

0

Answer 1

You are correct. I know it seems somewhat conter-intuitive, but an extended ball mount does not cut the capacity of the vehicle hitch yet a hitch extender does do that. Reason being the hitch extenders are typically much longer than the longer ball…

view full answer...

Answer 2

Although we don't have a 15-3/4 inch long ball mount with a 4-5 inch drop, we can get you pretty close to that. The Curt #C45270 measures 13 inches in length measured from the center of the hitch pin hole to the center of the hole where the…

view full answer...

Answer 3

The 2" Hitch Ball part #40038 has a 1" shank so the torque spec will be 250 ft. lbs.

view full answer...

Answer 4

A weight distribution system is not required to tow with your 2017 Dodge Grand Caravan, though a system is recommended if your trailer weight is more than 50 percent of your vehicle's GVWR. Even a small pop-up is going to surpass the 50…

view full answer...

Answer 5

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 6

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 11

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 12

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Recommended Portable Fire Pit That Works With The Ignik FireCan Fire Pit Rocks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching