Hitch for 1985 Chevy C10 with Deep Drop Bumper

Question

Question:

I have a 1985 Chevy C10 with a deep bumper. Trying to figure out if I need to pull the bumper and put a regular bumper on so I can safely tow with a hitch installed. Or can I just install a hitch that goes below the deep bumper. The question is will it be too low to tow anything? Id prefer to talk to someone.

asked by: Keith D

0

Expert Reply:

We have hitches that fit your 1985 Chevy C10 that has a deep bumper with the Curt hitch part # C13099. Your setup would definitely not be too low to tow with. A rise ball mount would make up for a lower hitch as well. I attached a help article

expert reply by: Jameson C

0

Answer 1

Outstanding photos thank you so much for sending them, and based on that we do have a hitch that can fit your 1965 Ford F-250 with a custom bumper. Since the frame is clear from any interference with the bumper, all you need to do is measure from…

view full answer...

Answer 2

Since you have a standard cab and chassis frame dimension on your shuttle bus we have the B and W Hitch part #BWHDRH25122 which will have mounting brackets that are spaced properly. It drops a bit more than 2 inches though. It's actually 5…

view full answer...

Answer 3

A roll pan bumper is a bumper that basically makes the rear bumper look as if it does not stick out further than the rest of the truck and that is molded into the rear of the truck. Its basically a cosmetic modification that you see on a lot of…

view full answer...

Answer 4

Sounds like on your taillight assemblies you have the stoplight and running light circuits backwards which is causing the circuits seem backwards in terms of brightness. So what I recommend is you reverse the wiring at the taillight assemblies and…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C13099 is a confirmed fit for a 1993 Chevrolet K3500 Pickup and it is designed for models with a deep drop bumper so it will work great for you. It offers a 5,000 lb weight capacity with standard 2"…

view full answer...

Answer 6

I reached out to my contact at Curt and was able to get a dimension sheet for the Curt Trailer Hitch Receiver - Class V #C15810 referenced in your question. I have attached an image of it for your review. This trailer hitch is designed to fit select…

view full answer...

Answer 7

I spoke with my contact at Curt about hitch #C13902. The overall width is approximately 41-1/2 inches. The bolt holes are approximately 39-1/2 inches apart on center.

view full answer...

Answer 8

The main difference between Draw-Tite trailer hitches #75033 and #75099 is the placement of the receiver tube on the cross member. On 75033 the receiver is attached to the rear part of the cross member. On 75099 it is welded below the cross member so…

view full answer...

Answer 9

I will be happy to help you out. Curt trailer hitch #13028 for your 1985 Chevy C-10 will likely fit without modifying the spare tire hanger/location provided that the tire size is a stock size and not an aftermarket larger size. If it is a larger…

view full answer...

Answer 10

The Curt 3-Piece Trailer Hitch Receiver #C15511 will fit a 1989 Chevy K1500 if it's the cab and chassis model. Since you have a pickup we need to find a different hitch. If your Chevy has the standard or step bumper then I recommend checking out…

view full answer...

Answer 11

The best way to tell if your 1989 Chevrolet K1500 is a Heavy-Duty (HD) or Light-Duty (LD) version would be to obtain your VIN and call the dealer as they would be able to tell you whether or not you have the HD or LD version. Another way to tell if…

view full answer...

Answer 12

The Draw Tite hitch part #41524 is a confirmed fit for a replacement for your 1995 Chevy K1500 pick up truck.

view full answer...

Hitch for 1985 Chevy C10 with Deep Drop Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching