MaxxTow Hitch Extender with Step Details

Question

Question:

Does MT70069 have a solid shank or is it hollow? Can you recommend 2 inch to 2 inch hollow hitch extension models of similar length to MT70069. Thanks!

asked by: Chris

0

Expert Reply:

The MaxxTow Hitch Extender with Step, part # MT70069 is a hollow hitch extender. I've attached a video where they mount a High/low adapter through the extender and its shank is roughly the same length as the useable part of the hitch extender before its shank.

expert reply by: Jacob W

0

Answer 1

What Gen-Y said is correct, and this is the best solution for a problem like yours. The Replacement Shank for Gen-Y Adjustable Ball Mount - 2" Hitch - 7-1/2" Drop/Rise - 16K #325-GH-504 will not reduce your tongue weight capacity at…

view full answer...

Answer 2

We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

MaxxTow Hitch Extender with Step Details

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching