Can Curt Hitch for 2020 Ford Escape Install without Die Grinder

Question

Question:

Hello, I have a 2020 Ford Escape SE Sport Hybrid AWD and am wanting to install this hitch. I do not have a die grinder, so would i still be able to install the hitch through the existing holes without enlarging them? I will only be using the hitch for a bike rack so I do not need much towing capacity. Thank you.

asked by: Chip B

0

Expert Reply:

The Curt hitch part # C23FR is a fit for your 2020 Ford Escape Hybrid and can install without a die grinder or any power tools. You can use a file to enlarge the hole which is a very common approach. Or a drill could work too if you happen to have one.

expert reply by: Jameson C

0

Answer 1

No, you will not have to trim the bumper to install the Curt #C23FR on your 2023 Ford escape. This will be a fairly easy bolt on install. You may have to use a drill to enlarge a few of the holes in the frame in order to fit your fasteners, but it is…

view full answer...

Answer 2

The upright arm on the Thule T2 Pro XTR Bike Rack for 2 Bikes part #TH83JV can be replaced yes, that said you must buy this as an assembly with the tray. The Replacement Spar Tube Assembly for Thule T2 Pro XT part #7524703001 for the one closest to…

view full answer...

Answer 3

With the Curt hitch part #C23FR installed on your 2020 Ford Escape Hybrid you'd have limited access to the hands free liftgate function. You'd still be able to kick your foot to either side of the hitch tube but for the best result relocating…

view full answer...

Answer 4

The main difference between the Curt #C23FR and etrailer #e89YR for your 2022 Ford Escape is the finishes. The Curt #C23FR has a glossy black finish and the etrailer #e89YR has a matte black finish. Their capacities and installations are the same. It…

view full answer...

Answer 5

For your 2022 Ford Escape Hybrid I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C23FR. This hitch has a simple bolt-on installation with all necessary hardware included. Curt's gloss black powder coat finish over…

view full answer...

Answer 6

The hand knob on the Thule T2 Pro XTR 2 Bike Platform Rack #TH83JV has a lock cylinder on it. So once you put the T2 into your 2018 Honda Odyssey's 2" hitch such as #e98855 and the Auto Pin goes through the hitch pin hole and shank it cannot…

view full answer...

Answer 7

The only way for you to get the new hitch lock wheel assembly is with replacing the entire 2" Lower Assembly #TH37MY. This is the only way the parts that you are needing are available for the Thule XT Bike Rack.

view full answer...

Answer 8

With the etrailer #e89YR hitch installed, the receiver tube will block the sensors in the middle of the bumper, but if you wave your foot several inches to the right or left of the receiver, the sensors will pick up the movement and operate the…

view full answer...

Answer 9

For your 2022 Ford Escape non-hybrid there are two trailer hitch receiver options, the Curt #C23FR, and the etrailer #e89YR. Both of these hitches share the same hidden crosstube design so that when the hitch is installed the only visible portion is…

view full answer...

Answer 10

For your 2022 Ford Escape Hybrid we have the etrailer hitch part #e89YR as a confirmed fit which is a really great option. It's mostly hidden and has great towing capacities as well. Only the hitch opening hangs below the rear bumper which allows…

view full answer...

Answer 11

Everything I found about the factory hitch for the 2020 Lincoln Corsair says it is either not intended for use with the Hands-Free Litigate or that you'll need to have your sensors re-located. There is no note from Curt about their hitch that…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...