Which Trailer Hitch for 2002 Subaru Outback Sedan

Question

Question:

Model....smallest lightest easiest for 02 subaru outback sedan for carrying light loads. am hoping for something like Curt Trailer Hitch Receiver - Custom Fit - Class II

asked by: Mike S

0

Expert Reply:

We offer a Curt # C12270 or a Draw-Tite # 36284 Class II receiver hitch for your 2002 Subaru Outback Sedan.

Both hitches would install in the same manner, with a couple of slight differences. Both hitches have the same 3000 lb towing capacity (limited to the 2000 lb towing capacity of the vehicle) but the Curt has a 350 lb tongue weight capacity while the Draw-Tite has a 300 lb tongue weight capacity.

The crossbar of the Curt routes under the exhaust pipe while that of the Draw-Tite is routed above it. This difference is purely cosmetic, but I prefer to have the crossbar pass over the top of the exhaust pipe, I feel it looks better and provides better ground clearance (see photo). As far as quality goes, the hitches are both high-quality. If the way the crossbar is situated to the exhaust pipe isn't important to you, you can choose the least expensive model without feeling like you've sacrificed anything.

The Curt # C12097 you'd looked at isn't a fit for your vehicle.

If you'll be towing with the hitch, you'd need a few more items to complete your towing system. For a trailer wiring harness, use # C59496. For a ball mount, use # C45026 and # A-80 for a 1-7/8 inch or # A-82 for a 2 inch trailer ball.

If you click the provided link, you can see install videos for either hitch mentioned above.

expert reply by: Mike L

0

click to enlarge

Answer 1

I can give you the dimensions of the Curt hitch for the Volkswagen Tiguan, part #C12097, but I can't guarantee whether or not it'll fit your vehicle. All of the products we carry are designed specifically for vehicles manufactured for the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...