Height of Upper and Lower Cam Brackets of Polar Cam Action Door Latch Kit # PLR658-002

Question

Question:

how much clearance under the door is necessary to mount the receiving brkts? How tall are they? Thanks

asked by: Michael

0

Expert Reply:

The height of the Polar Cam Action Door Latch Kit # PLR658-002 brackets you referenced is 2 inches so you'd need 2 inches basically above and below the door for the brackets to fit.

expert reply by: Jameson C

0

Answer 1

Based on your image it looks like you only need a Replacement Handle Assembly #PLR158-100-SS welded onto the cam lock that you already have. If the entire assembly needs replaced the Cam-Action Lockable Door Latch w/ Split Bushings for Large Enclosed…

view full answer...

Answer 2

According to the manufacturer the pipe is the 1 inch schedule 40 pipe which means the inner diameter is 1 inch and the outer diameter is 1-5/16" so the attached video and the video are correct. I have also attached a photo from the manufacturer…

view full answer...

Answer 3

The big difference between the Cam Door Latch #PLR458-018 and the #PLR658-002 is the robustness of the pipe mount on the handle side. The #PLR658-002 is more for heavy duty applications and comes with bushings for the pipe to mount in. This requires…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Height of Upper and Lower Cam Brackets of Polar Cam Action Door Latch Kit # PLR658-002

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching