What Gauge and Composition Are the Wires on the LED Combination Trailer Tail Lights by Optronics

Question

Question:

What gauge is the wire and is it solid copper or copper coated aluminum

asked by: Greg

1

Helpful Expert Reply:

I reached out to my contact at Optronics and they were able to give me some additional information on this light set. The LED Combination Trailer Tail Lights # TLL16RK have full copper wires that are 18 gauge wires.

expert reply by: Erik B

1

Answer 1

Thanks for the photo of your trailer! Based on the photo you sent in, it looks like the Bargman LED Trailer Tail Light #47-06-404 that you referenced will work well for you. This light measures 6-1/2 inches long x 2-1/4 inches tall and is designed to…

view full answer...

Answer 2

Yes, the Peterson LED Identification Light Bar #M191-3RL that you referenced would work great on your 2005 Nitro boat trailer as this is submersible and universal enough that it can easily be made to fit a boat trailer like yours.

view full answer...

Answer 3

To determine what you will need as far as trailer lighting is concerned you will need to go out and measure the dimensions of your trailer. Once you know the overall length and width check out the FAQ article I attached to the right. It will walk you…

view full answer...

Answer 4

We have the Waterproof, Over 80" LED Trailer Light Kit with 25' Wiring Harness #TLL16RK that would basically come with everything you'd need. It comes with two LED trailer taillight assemblies, all new wiring for them and the trailer,…

view full answer...

Answer 5

There would be a noticeable difference if you had both the Aero Pro light #STL37RB and the Glolight, #STL117RB right next to each other. You would notice that the Glolight seams to actually sort of glow rather than just light up. This is due to the…

view full answer...

Answer 6

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 7

We actually have two red LED lights that are 15 inches long and 1-3/8 inches wide that have a 14-1/8 inch hole spacing. Parts #MCL70RB and #MCL70RBF2. They will both fit into your chrome base, #A69CB.

view full answer...

Answer 8

Yes, the only difference between these light bars is that the #MCL97RPG has the 0.180 male bullet at the end of the wire and the #MCL97RB just has a regular wire you'd use a butt connector like part #DW05744-5 for the installation. Other than…

view full answer...

Answer 9

To use the Optronics Trailer Lights, item #STL22CCRB, on your boat trailer you will need several parts. I will list them below. 2 each Optronics Trailer Lights, item #STL22CCRB 2 each Rubber Grommet for 6-1/2 inch Oval Trailer Tail Lights, item…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What Gauge and Composition Are the Wires on the LED Combination Trailer Tail Lights by Optronics

Product Page this Question was Asked From

Continue Researching