Dimensions Of Replacement Drop Leg with Foot for etrailer and Ram Square Jacks

Question

Question:

is this a true 2 x 2 square tubing or 1 15/16?

asked by: Jammie

0

Expert Reply:

The Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks is a 2" x 2" square tubing drop leg. The leg is designed as a replacement for the etrailer or Ram square Direct Weld Jacks with a 7,000 lb capacity like part # TJD-7000 however it can be used to replace other 2" x 2" drop legs as well. I have attached a video for your reference.

expert reply by: Heather A

0

Answer 1

The short answer to this is, no, adding this hitch will not safely increase your tongue weight capacity. Since the tongue capacity for the vehicle is 350-lbs, upgrading to a hitch like the Draw-Tite Max Frame #DT78MR won't allow you to carry more…

view full answer...

Answer 2

For the Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks #TJD-7000-FT you are going to need the: -Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks #TJP-PN58, which is a 5/8" diameter pin.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...