What Pull Pin Is Used With the Replacement Drop Leg with Foot for etrailer and Ram Square Jack?

Question

Question:

Which pull pin will I need to purchase with this item ?

asked by: Walter S

0

Expert Reply:

For the Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-FT you are going to need the:

-Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks # TJP-PN58, which is a 5/8" diameter pin.

expert reply by: Bryce D

0

Answer 1

The Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks is a 2" x 2" square tubing drop leg. The leg is designed as a replacement for the etrailer or Ram square Direct Weld Jacks with a 7,000 lb capacity like part…

view full answer...

Answer 2

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 3

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 4

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 5

The best trailer we offer for your two Titan Propel 12 Kayaks is the Yakima Rack and Roll Trailer part #Y08107 paired with the Heavy Duty Shocks for Yakima Rack and Roll Trailer part #Y08110. The reason that I recommend the Rack and Roll is because…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

What Pull Pin Is Used With the Replacement Drop Leg with Foot for etrailer and Ram Square Jack?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching