Does the Exhaust Have To Be Lowered On a 2019 Chevrolet Equinox To Install the etrailer Hitch

Question

Question:

Does the exhaust have to be lowered in order to install this hitch on a 2019 Equinox non-diesel? Do you have a video? Thanks.

asked by: Dale T

0

Expert Reply:

The exhaust does not have to be lowered to install the etrailer.com Trailer Hitch Receiver part # E59ZR on your 2019 Chevrolet Equinox. The installation process is very simple even for the most inexperienced of installers and it should only take you around 40 minutes or so with the proper tools (sockets, ratchet etc.). I have attached a video for you on the install process which will be the same as the Curt Trailer Hitch Receiver part # C77FR.

expert reply by: Conner L

0

Answer 1

We have a Curt hitch that does fit your 2019 Chevy Equinox with the #C77FR but the #C13900 that you referenced is a multi-fit hitch which hasn't been tested on your vehicle so we can't recommend it as a fit. Just based on the bracket height…

view full answer...

Answer 2

For your 2019 Chevy Equinox the Draw Tite hitch part #76419 is a confirmed fit and would work well. It is a 2 inch hitch like you need with plenty of capacity and also is mostly concealed too. For trailer you'd want the part #119250KIT for a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

I do have a few items you can look for that will give you an idea as to whether or not your 2018 Chevrolet Equinox came equipped with the factory tow package (K5L) or not but the only sure fire way to tell would be to obtain your VIN and contact the…

view full answer...

Answer 6

The Curt Vehicle Wiring Harness #C94FR that you referenced is supposed to be used if your 2019 GMC Terrain came with the factory tow package. If those fuse locations are empty, then it sounds like you don't have the factory tow package. As of…

view full answer...

Answer 7

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 8

the CE Smith guide-ons #CE27610 are approximately 15 degrees off 90 degrees. So that would be 75 or 105 degrees depending on which way the guide-on was facing.

view full answer...

Answer 9

You are correct that the roller style guide-ons #CE27610 are not meant to support weight. But the boat brushing up against them is to be expected and they will work fine for that. A little bit of space like you said will help to make sure the boat…

view full answer...

Answer 10

Hey Scott, the bolt holes of the Dexter DX7.5L A-60 Brake Actuator w/ Electric Lockout - Disc #DX56FR are 3" apart horizontally and 2-1/2" apart vertically. The holes are 5/8" from the top and bottom of the actuator.

view full answer...

Answer 11

Your surge coupler will have either a sticker or an engraving on it, typically near where the coupler is located. If you can get me that information and what you're needing to replace on it I'd be more than happy to help you find what…

view full answer...