1-11/16" Round. Waterproof, LED trailer light with 2 diodes serves as either a side marker or clearance light. Durable polycarbonate housing and lens. Surface mount - hardware not included. 2-Wire pigtail with 0.18 male bullets. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated or P3-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello, everybody. This is Jeff at etrailer.com. Today, we're going to take a look at this M3 LED red clearance or side marker trailer light. Now this round trailer light will serve as either a side marker or a clearance light. It is a P2 rated light, so it does produce a 90 degree beam pattern.It is sonically sealed, waterproof housing and lens unit is submersible. Now it does use LEDs which make great replacements for incandescent lights because it'll last 50 times longer.
They're more efficient because they'll provide brighter light with less power output. And of course, no bulbs to replace or brittle filaments to break.This is a nice durable polycarbonate lens and housing. It has red diodes with the red lens. This is compatible with 12 volt DC systems, and it is designed to mount on the surface of the trailer. Now the hardware to install this is not included.
They do also offer a chrome bezel that we do sell separately on our website. It'll provide a nice finished look if you prefer.And if you'll notice, on the back of the light, it has the two wire pigtails with the male bullet connectors, and they're both red wires. So they're not polarity sensitive. You could use either wire for either function. At the end of this video, I am going to hook this up just to show you how bright the light is.This light is department of transportation compliant.
Few dimensions on this light. The diameter, the light itself, is going to be right at one and 11 sixteenths inches. A depth on it, now we're going to measure from the front to the back here. Sticks out is about one and three quarter inches. Does use two LEDs.
The power draw on this light at 12.8 volts is 0.12 amps.So what I'm going to do now is we're going to hook this up to some power, show you how bright the light is. And as I mentioned, it doesn't matter which one's power, which one's ground. Use either one for either function. And now with them both connected, we'll go ahead and turn on our 12 volt power and you can see there's the red light. Go ahead and turn off the overhead lights and you can see how bright it is. Can be used as a clearance light or a side marker trailer light.There's your pattern it gives off. We'll go ahead and turn back on the overhead light. Turn off our power. But that should do it for the review on the M3 LED red clearance or side marker trailer light.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.