How To Help Ensure the Phoenix USA QuickTrim Hub Covers Do Not Fall Off

Question

Question:

Do you have any recommendations on how to keep these from falling off when going down the road ?

asked by: Phil

1

Helpful Expert Reply:

If you are having issues with the Phoenix USA QuickTrim Hub Cover part # QT655C falling off then I recommend wrapping a few of the lug nuts with electric tape so the cover will then have a tighter grip. This should work to help fix your issue but if it does not then please just let me know.

expert reply by: Conner L

1

Answer 1

Yes. The Phoenix USA QuickTrim Hub Cover - 8 on 6-1/2" Bolt Circle - ABS Plastic - Chrome - Qty 1 #PXQT765CHN typically will fit on 13/16" lug nuts; when you convert to metric that's about 20.5mm, so the .5mm would be within…

view full answer...

Answer 2

The Phoenix USA #PXQT965CHN QuickTrim Hub Cover fits wheels with an 8 lug on 6-1/2 inch bolt circle with 1-1/16 inch lug nuts, regardless of the wheel stud size. If your existing wheel meets those parameters, the #PXQT965CHN QuickTrim Hub Cover…

view full answer...

Answer 3

Our best chrome wheel covers we offer for an 8 lug trailer wheel is the part #PXQT965CHN which is made by Phoenix USA. These basically just snap right into place, but they stay on very well and look great too.

view full answer...

Answer 4

The style of lug nut that the reviewer you referenced is referring to would be like the Americana Trailer Lug Nut part #AM26NR. You'll notice it has a lip around the base near where it contacts the wheel. That lip works great with the Hub…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

How To Help Ensure the Phoenix USA QuickTrim Hub Covers Do Not Fall Off

Product Page this Question was Asked From

Continue Researching