Fit of Phoenix USA Hub Cover on 8 Lug Wheel With 5/8 Inch Wheel Studs

Question

Question:

Will this fit on a hub with 8 5/8inch lugs?

asked by: Charlotte B

0

Expert Reply:

The Phoenix USA # PXQT965CHN QuickTrim Hub Cover fits wheels with an 8 lug on 6-1/2 inch bolt circle with 1-1/16 inch lug nuts, regardless of the wheel stud size. If your existing wheel meets those parameters, the # PXQT965CHN QuickTrim Hub Cover will work perfectly for you. I've linked to a product description video featuring the hub cover.

A 5/8 inch wheel stud will typically use a 1-1/16 inch lug nut, so you should be good to go. I've linked to a help article that shows how to identify your wheel bolt pattern, I hope you find it helpful.

expert reply by: Mike L

0

Answer 1

The correct grease cap for the Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles #DX46XR is the #TRU66FR.

view full answer...

Answer 2

To measure the pilot hole on your wheel, you will need to remove the cap in the picture and then measure the inside diameter of the hole in the wheel. Most wheels with the bolt pattern you have in the photo are 4.88 inches or 4.9 inches with a select…

view full answer...

Answer 3

If you are having issues with the Phoenix USA QuickTrim Hub Cover part #QT655C falling off then I recommend wrapping a few of the lug nuts with electric tape so the cover will then have a tighter grip. This should work to help fix your issue but if…

view full answer...

Answer 4

The style of lug nut that the reviewer you referenced is referring to would be like the Americana Trailer Lug Nut part #AM26NR. You'll notice it has a lip around the base near where it contacts the wheel. That lip works great with the Hub Covers…

view full answer...

Answer 5

Our best chrome wheel covers we offer for an 8 lug trailer wheel is the part #PXQT965CHN which is made by Phoenix USA. These basically just snap right into place, but they stay on very well and look great too.

view full answer...

Answer 6

Yes. The Phoenix USA QuickTrim Hub Cover - 8 on 6-1/2" Bolt Circle - ABS Plastic - Chrome - Qty 1 #PXQT765CHN typically will fit on 13/16" lug nuts; when you convert to metric that's about 20.5mm, so the .5mm would be within the margin…

view full answer...

Answer 7

In the diagram that you referenced, that I also attached here, the brake output circuit is a separate circuit that carries power to the trailer brakes totally separate from the brake light circuits. Also, the 12 volt power source is a separate…

view full answer...

Answer 8

The break away system on a trailer would typically have its own battery, like that shown with part #20400. The reason that pulling your break away switch does not actuate your brakes is that it is not wired correctly. The break away switch should be…

view full answer...

Answer 9

The Lippert 7,000 lb axles use a seal that is 2.250 inches inner diameter and 3.376 inches outer diameter. You will want Grease Seals 10-36 (pair) #RG06-070 for the replacements or complete bearing kit #BK3-200 which includes replacement bearings,…

view full answer...

Answer 10

Going from the tire size of 205/75-15 to 225/75-15 is a pretty common change for trailer wheels. There are two things you'll want to verify though. First is that your wheel is either 6 inches wide or 6-1/2 inches wide. Those two widths are the…

view full answer...

Answer 11

Since wheels will be able to withstand the psi rating of any of the tires that are meant to fit it you will need to look at the valve stem as that is the deciding factor. If your valve stem has the rubber all the way up to the threads, like part…

view full answer...

Fit of Phoenix USA Hub Cover on 8 Lug Wheel With 5/8 Inch Wheel Studs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching