Drill Bit for 2-1/2" Long Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood

Question

Question:

Where can I purchase the drill bits needed to get the 1 1/2 inch Torx screw installed?

asked by: Steve A

0

Expert Reply:

You can use the TRX 30 Bit # TX430-1 for the 2-1/2" Long Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood # TFX250ACQ. You should also be able to acquire a bit this size at your local hardware or home improvement store.

expert reply by: Jon G

0

Answer 1

I would recommend to use the treated torx screws for ACQ (Alkaline Copper Quaternary) treated wood for better corrosion and rust resistance. The treated torx screws like the Redline 2-1/2 Inch Long Torx Trailer Screw for ACQ Treated Wood, part…

view full answer...

Answer 2

I would go ahead and use the same holes that are already on your trailer. just make sure that they are the 7/32" diameter needed for the 2-1/2" Long Torx Screw #TFX250ACQ and that they have a good grip. If the screws don't seem to hold…

view full answer...

Answer 3

I would recommend to use the treated torx screws for ACQ treated wood for better corrosion and rust resistance. The treated torx screws like the Redline 2-1/2 Inch Long Torx Trailer Screw for ACQ Treated Wood, part #TFX250ACQ, are plated with a…

view full answer...

Answer 4

It would be a good idea to go with different holes for the reinstallation of the deck boards on your trailer, or at least enlarge the ones you have and then go with the next thicker screws so that you know you are getting a good grip on the metal…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...