Are Bolts Included With the Replacement Head for Curt MV Weight Distribution Systems Part # C17075

Question

Question:

Does the Replacement Head for Curt MV Weight Distribution Systems Item # C17075 come with the bolts to mount to the Curt Adjustable Weight Distribution Shank - 8inch Item # C17100?

asked by: Anthony G

1

Helpful Expert Reply:

The Replacement Head for Curt MV Weight Distribution Systems part # C17075 does not come with the bolts that you will need to attach it to the Curt Adjustable Weight Distribution Shank part # C17100. For this, you would also need the Replacement Bolt Kit for Curt MV Weight Distribution Systems part # C17076.

expert reply by: Conner L

1

Answer 1

Curt offers one replacement weight distribution head which is for the Curt MV round bar setups, part #C17075. The spring bars that fit the Curt MV replacement head are 1-1/2" diameter, like #C17073.

view full answer...

Answer 2

Sorry to hear that about your Curt MV Weight Distribution System w/ Friction Sway Control #C17063! We do have replacement parts available for this system. Here are various pieces of the head unit that you might need: Adjustable Shank - #C17100…

view full answer...

Answer 3

The Curt Adjustable 2-Ball Mount #C79NR is going to be 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. This has the 2-1/2" shank you are looking for and can be adjusted from 4-1/2" of rise to…

view full answer...

Answer 4

If you are talking about the pins for the spring bar retainer clips there is a kit you can use #17109 which includes the pins, clips, and retaining screws. If none of these are the parts you are looking for then I have included a link to all of the…

view full answer...

Answer 5

The Blue Ox SwayPro Weight Distribution Shank #BXW4017 would be a great solution for you. Based on the picture you sent in you are currently using the height setting that the #BXW4017 provides so this shank would be an excellent solution.

view full answer...

Answer 6

The Curt Hitch Adapter #C45405 will not reduce the tongue weight of your hitch. Many adapters that extend the length will reduce towing capacity based on tongue weight, but this adapter isn't one of them. It will work fine with the Curt TruTrack…

view full answer...

Answer 7

Generally speaking the use of a reducer sleeve does not decrease the capacity of a trailer hitch. However some hitch manufacturers may have a reduced capacity if a sleeve is used. There isn't a standard for all hitches and all reducer sleeves. It…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...