Installing Fusion LED Combo Tail Light Bar # STL264RB on RV with Separate Wiring System
Question:
On my RV I’m installing these. The wiring on the RV has a wire for turn signal and a separate wire for brake lights. Can I connect these 2 wires to the to the 1 wire on light for turn and brake ?
asked by: Paul S
Helpful Expert Reply:
Both the turn signal and brake light wire on your RV can be spliced directly to the stop/turn signal light wire on the Fusion LED Combination Tail Light Bar # STL264RB but the bar isn't going to function perfectly. This is because when braking and turning at the same time, the brake light is going to override the turn signal so that the bar remains constantly lit instead of blinking in this scenario.
If you are okay with this then the light bar will work well.
Otherwise you will want to use a 3-to-2 wire converter like the Roadmaster # RM-732 to combine the circuits before the light bar. This will both combine those separate circuits on the RV as well as ensure the turn signal overrides the brake light when both are activated at the same time so that the light bar flashes.
If you happen to have a 4-Way trailer connector on the RV you could also tap directly into those wires, as the 4-Way would already be converted to the needed combined wiring system.
Products Referenced in This Question
Roadmaster Brite-Lite Wiring Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- Roadmaster
more information >
Product Page this Question was Asked From
Fusion LED Combination Tail Light Bar for Trailers Over 80" Wide - Submersible - Red/Clear Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail/Backup
- Strip Light
- Surface Mount
- Submersible Lights
- LED Light
- 20-1/2L x 1W Inch
- Red and White
- Optronics
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Optronics Fusion LED Combination Tail Light Bar Installation
- Shop: Fusion LED Combination Tail Light Bar for Trailers Over 80" Wide - Submersible - Red/Clear Lens
- Shop: Hopkins Endurance 4-Way Flat Trailer Connector w/ 48" Harness and Ergonomic Pull
- Shop: Curt Mounting Bracket for 4-Pole Flat Trailer Connector
- Shop: Hopkins Fold-Over Mounting Bracket for 4-Way Flat Trailer Connector
- Shop: Chrome Mounting Bezel for Optronics ThinLine Combination LED Tail Light - 20-1/2" Long
- Shop: Hopkins Endurance 4-Way Flat Trailer Connector - Trailer End - Ergonomic Design
- Shop: LED Trailer Mini Clearance and Side Marker Light with Grommet - Submersible - 1 Diode - Amber Lens
- Shop: RV Exterior Lighting
- Search Results: 44649
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 68149
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Video: Lippert Solera Slider Slide-Topper Review
- Shop: Trailer Wiring
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Shop: Fifth Wheel Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Video: Choosing the Right Brake Controller
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Search Results: dust cap
- Shop: Suspension Enhancement
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome