Curt Adjustable Pintle Hitch Compatibility With InfiniteRule Locking Pins

Question

Question:

will the InfiniteRule Locking Pins for B and W Tow and Stow 10K and 14.5K Ball Mounts - Keyed Alike - Qty 4 Item # 34061701D work with the Curt Pintle Hitch?

asked by: Craig S

0

Expert Reply:

Yes. The InfiniteRule Locking Pins for B & W Tow and Stow 10K and 14.5K Ball Mounts - Keyed Alike - Qty 4 # 34061775-D have pin diameters of 5/8 inch and spans of 4-1/18 inches and 3-1/8 inches. The Curt Pintle Hook with 2-5/16" Ball - 2" Hitches - 13,000 lbs # C45910-15-20 uses 5/8 diameter pins that are 4-1/4 inches 3-1/4 inches based on the designed locks # C23556. The Infinite Rule Locking pins will absolutely work for this application.

expert reply by: Jason S

0

Answer 1

With pintle hitch trailers typically being a very high weight they do not offer one for a 1-1/4" receiver due to the light duty capacity of the small receiver. I do see you input your vehicle as a 2016 Ford Explorer which we do offer a 2"…

view full answer...

Answer 2

In order to obtain the Curt Adjustable 2-Ball Channel Mount part #C45926 with a pintle ball combo you can go with the Curt Pintle Hook with 2-5/16" Ball part #C45910-15-20 or just obtain the Curt Adjustable 2-Ball Channel Mount and purchase the…

view full answer...

Answer 3

Yes, the Reese lock will work with the Curt Slim Adjustable 2-Ball Channel Mount #C46KR. You could also use the etrailer #e98882 or any other similar lock with a 5/8" diameter to secure it.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...