Trailer Wiring Recommendation for 2006 Mazda Tribute That Doesn't Require Finding Relay Location

Question

Question:

I saw on a post it said the relay would have to be installed in a block behind the dash please explain

asked by: Wade B

0

Expert Reply:

While I have a much easier trailer wiring solution than the # 40455 that you referenced for your 2006 Mazda Tribute there is a good chance you'd have to have a relay installed behind the dash board of your vehicle to have the circuits active for this kit to work. Since most of our customers have come back and stated that finding the relay was a headache the much better option is to go with a harness that installs by plugging inline with the taillight circuits of the vehicle.

For that I recommend the Tekonsha kit part # 118426 which is a custom fit and has our most reliable converter box. The install requires a bit more wiring than the Hopkins kit but there's no guesswork and no headache of trying to track down the correct relay and also where it installs. We've heard that several Ford dealers have a hard time finding the relay location.

expert reply by: Jameson C

0

Emilio V.

7/23/2020

That is a good recommendation. However, I did purchase the plug and tow and the relay. I made an investment so I need to work with what I have because I do not have the cash.

Reply

Answer 1

The dealer will be able to tell you whether or not your 2006 Ford Escape has the factory tow package but the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #C56345 works on models both with or without so this is what…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...