What Does NC on Primus IQ Brake Controller Mean When Starting Vehicle and Then Disappearing?

Question

Question:

Brake controller shows NC when starting vehicle then goes blank. Pushing button used to show something. What the code nc?TK90160

asked by: Ken J

0

Expert Reply:

The NC on your Tekonsha Primus IQ Brake Controller # TK90160 is simply showing power to the brake controller without a trailer connected. It should do this and display for a 15 seconds before going away. The NC means the brake controller is seeing no trailer connection.

The button being pushed should not show anything when a trailer isn't connected. When a trailer is connected it would give you a power output range between 0.0 volts and 13 volts. I've attached a photo of part of the owners manual and have attached the complete manual labeled installation details to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

To use the Curt Echo Wireless Trailer Brake Controller #C51180 your vehicle only needs 12 volt, ground, and turn signals connected to its 7-way socket. What this means is you do not need the brake signal from the 7-way. For example, if you used a…

view full answer...

Answer 2

It sounds like there is an electrical short on your trailer wiring that is activating your left rear brake assembly and that is why the brake continues to drag and get hot. Since you have swapped the brake assembly out and still had the problem you…

view full answer...

Answer 3

The weak pulsing you are seeing is normal on the output pin of the connector. That pulse is actually your brake controller constantly testing to see if a trailer is connected. Basically it's looking for a low amperage draw when it applies the…

view full answer...

Answer 4

As long as the 7-way connector on your 2021 Volkswagen Atlas has 12v power the Autowbrake Electric Brake Controller - Trailer Mount - 1 to 3 Axles - Proportional #3430001 you were looking at will work just fine and is a great option as it installs on…

view full answer...

Answer 5

The controller is only putting out voltage when the manual switch is applied on the brake controller, but not when the vehicle brakes are applied, is that correct? The most likely problem is that the controller is not getting the input that the…

view full answer...

Answer 6

On some vehicles, the key has to be on for voltage to go back to the trailer connector. On others, it does not. An electric brake controller will always send back some minimal voltage to the trailer connector. This is how it senses if there is a…

view full answer...

Answer 7

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 8

The white wire from the Autowbrake Electric Brake Controller #3430001 is for ground so you will just want to make sure it's securely attached to a clean bare metal surface. A weak ground can definitely prevent proper operation on the brake…

view full answer...

Answer 9

My technical contact at Tekonsha informed me that an OC error code is typically displayed on a Hayes manufactured product. The error OC translates to open circuit, which indicates that there is not a proper connection to the trailer brakes. This is…

view full answer...

Answer 10

There are 3 possible causes for the display reading - No Trailer Connected - on the Tekonsha P-3, Item #90195, when the trailer is connected. The first cause could be that you do not have the P-3 set up in the Hydraulic mode. On page 4 the…

view full answer...

Answer 11

In order to switch from your electric brakes to a disc brake system there are several things you will want to consider. It is true that the disc brakes will provide better braking for you, although converting can require an involved installation.…

view full answer...

Answer 12

Yes, there is another option to add a brake controller to your Ranger. Since you have the factory tow package, I recommend the Curt Echo In-Line Wireless Brake Controller item #C79DR. The controller plugs in behind your 7-way with included…

view full answer...