Recommended Brake Controller for a 2023 Ford Ranger w/ Factory Tow Package

Question

Question:

I have a 2023 Ford Ranger with 7-way on the bumper. I need a brake controller and do not want to hardwire one and am not really sure about the reliablity and security of the plug in one on the bumper. Are there any other options?

asked by: Andres

0

Expert Reply:

Yes, there is another option to add a brake controller to your Ranger. Since you have the factory tow package, I recommend the Curt Echo In-Line Wireless Brake Controller item # C79DR. The controller plugs in behind your 7-way with included connectors. This will completely eliminate any need to hardware a controller.

The Echo In-Line is a proportional brake controller that slows or stops your trailer when your Ranger decelerates. It uses Bluetooth to communicate with your phone so you will never have to worry about losing signal. If your phone dies it automatically uses the default settings you program in.

If you like the reassurance of a manual override button you will want the Manual Override Button for Curt Echo Brake Controller item # C83HR. You can mount it wherever you want it inside your vehicle.

This is a much better option if you are worried about the Echo item # C51180 getting lost or stolen. I have linked a review video along with a couple of pictures that shows the Echo In-Line item # C79DR installed.

expert reply by: Jerred H

0

Curt Echo In-Line Wireless Brake Controller
(click to enlarge)

Westin E-Series Round Nerf Bars
(click to enlarge)

Answer 1

It is possible to have both a 7-way and 4-way on your 2019 Ford Ranger by using the #C56431 but you will need to replace the 7-way connector with the #C55774 and you'd have one that has both. This uses the same round connector as what comes…

view full answer...

Answer 2

Based on your measurements you are looking for a 4-1/4 or 4 inch drop for your ball mount. I've attached an article to assist. If you want a fixed mount ball mount, I recommend the4 Curt Class III Ball Mount with 2" Ball -…

view full answer...

Answer 3

The best hitch for your 2023 Ford Ranger is going to be the etrailer Hitch item #e63ZR. This hitch is custom fit and bolts to your Ranger with included hardware. I really like the etrailer hitch because it installs behind your rear bumper and the…

view full answer...

Answer 4

There is not any added hardware required to install the Curt hitch that fits your 2022 Ford Ranger, which is the following part number: - Curt Trailer Hitch Receiver #C13417 Installation of the #C13417 on a '22 Ranger just requires removing the…

view full answer...

Answer 5

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 6

We do have some trailer hitch and wiring options for your 2019 BMW X3. For a hitch I recommend using the Draw-Tite Class III #76226 as it fits all models of your X3. Then for wiring you'll need the T-One #TK77FR which tees in behind your tail…

view full answer...

Answer 7

To add a 7-way connector to your 2023 Ford Ranger you will want the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector item #C56431. This custom-fit T-connector plugs into your Ranger's wiring harness, which is located behind…

view full answer...

Answer 8

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 9

The Curt Echo #C51180 Troubleshooting Guide offers three possible solutions to the resolve the "Overload" issue. 1. Reconnect the trailer connector. 2. Confirm vehicle 7-way connections and wiring. 3, Check trailer brake wiring for short…

view full answer...

Answer 10

The trailer connected message is an issue with 2019 Ford Rangers, particularly with their 7-way wiring harnesses, and since the Curt Echo In-Line Wireless Brake Controller #C79DR installs in-line with the harness, it may have exacerbated the issue.…

view full answer...

Answer 11

To use the Curt Echo Wireless Trailer Brake Controller #C51180 your vehicle only needs 12 volt, ground, and turn signals connected to its 7-way socket. What this means is you do not need the brake signal from the 7-way. For example, if you used a…

view full answer...

Answer 12

We have not yet (as of April 2019) had a chance to install any wired trailer brake controllers on a 2019 Ford Ranger so for guidance I checked with my most trusted brake controller expert at Tekonsha. Based on what I could learn about the truck if…

view full answer...